2018 newest Cisco CCDP 300-115 dumps exam questions and answers free download from leads4pass. Prepare for Cisco 300-115 exam test with the best Cisco CCDP 300-115 dumps pdf files and vce youtube demo update free shared. “Implementing Cisco IP Switched Networks” is the name of Cisco CCIE Wireless https://www.leads4pass.com/400-351.html exam dumps which covers all the knowledge points of the real Cisco CCIE Wireless. High quality latest Cisco CCDP 300-115 dumps pdf training resources and study guides free download, 100% success and guarantee to pass Cisco 300-115 exam test easily at first attempt.
Download free latest Cisco 300-115 dumps pdf files: https://drive.google.com/open?id=0B_7qiYkH83VROUdnZWRYLTJta1E
Download free latest Cisco 300-135 dumps pdf files: https://drive.google.com/open?id=0B_7qiYkH83VRS21DRS14UlZHNjg
High Quality Cisco CCDP 300-115 Dumps Exam Questions And Answers (1-30)
QUESTION 1
Which statement about the use of SDM templates in a Cisco switch is true?
A. SDMtemplates are used to configure system resources in the switch to optimize support for specific features, depending on how the switch is used in the network.
B. SDM templates are used to create Layer 3 interfaces (switch virtual interfaces) to permit hostsin one VLAN to communicate with hosts in another VLAN.
C. SDM templates are used to configure ACLs that protect networks and specific hosts from unnecessary or unwanted traffic.
D. SDM templates are used to configure a set of ACLs that allows the users tomanage the flow of traffic handled by the route processor.
E. SDM templates are configured by accessing the switch using the web interface.
Correct Answer: A
QUESTION 2
How does VTP pruning enhance network bandwidth?
A. by restricting unicast traffic across VTP domains
B. by reducing unnecessary flooding of traffic to inactive VLANs
C. by limitingthe spreading of VLAN information
D. by disabling periodic VTP updates
Correct Answer: B
QUESTION 3
When using EtherChannel misconfiguration guard, which technology is used to prevent this type of misconfiguration from affecting the network?
A. STP
B. port security
C. LACP
D. PAgP
Correct Answer: A
QUESTION 4
After anEtherChannel is configured between two Cisco switches, interface port channel 1 is in the down/down state.
Switch A is configured with channel-group 1 mode active, while Switch B is configured with channel-group 1 mode desirable.
Why is the EtherChannel bundle not working?
A. The switches are using mismatched EtherChannel negotiation modes.
B. The switch ports are not configured in trunking mode.
C. LACP priority must be configured on both switches.
D. The channel group identifier must be different for Switch A and Switch B.
Correct Answer: A
QUESTION 5
Which feature describes MAC addresses that are dynamically learned or manually configured, stored in theaddress table, and added to the running configuration?
A. sticky
B. dynamic
C. static
D. secure
Correct Answer: A
QUESTION 6
Which database is used to determine the validity of an ARP packet based on a valid IP-to- MAC address binding? 300-115 dumps
A. DHCP snooping database
B. dynamic ARP database
C. dynamic routing database
D. static ARP database
Correct Answer: A
QUESTION 7
A network engineer changed the port speed and duplex setting of an existing EtherChannel bundle that uses the PAgP protocol. Which statement describes what happens to all ports in the bundle?
A. PAgP changes the port speed and duplex for all ports in the bundle.
B. PAgP drops the ports that do not match the configuration.
C. PAgP does not change the port speed and duplex for all ports in the bundle until the switch is rebooted.
D. PAgP changes the port speed but notthe duplex for all ports in the bundle.
Correct Answer: A
QUESTION 8
You want to configure a switched internetwork with multiple VLANs as shown above. Which of the following commands should you issue on SwitchA for the port connected to SwitchB? (Select the best answer.)
A. switchport mode trunk
B. switchport access vlan 5
C. switchport mode access vlan 5
D. switchport trunk native vlan 5
Correct Answer: A
QUESTION 9
Routers R1 and R2 are configured for HSRP as shown below:
Router R1: interface ethernet 0 ip address 20.6.2.1 255.255.255.0 standby 35 ip 20.6.2.21 standby 35 priority 100 interface ethernet 1 ip address 20.6.1.1.2 255.255.255.0 standby 34 ip 20.6.1.21 Router R2: interface ethernet 0 ip address 20.6.2.2 255.255.255.0 standby 35 ip 20.6.2.21 interface ethernet 1 ip address 20.6.1.1.1 255.255.255.0 standby 34 ip 20.6.1.21 standby 34 priority 100 You have configured the routers R1 andamp;R2 with HSRP. While debugging router R2 you notice very frequent HSRP group state transitions. What is the most likely cause of this?
A. physical layer issues
B. no spanning tree loops
C. use of non-default HSRP timers
D. failure to set the command standby 35 preempt
Correct Answer: A
QUESTION 10
Which technique automatically limits VLAN traffic to only the switches that require it?
A. access lists
B. DTP in nonegotiate
C. VTP pruning
D. PBR
Correct Answer: C
QUESTION 11
Which four LACP components are used to determine which hot-standby links become active after an interface failure within an EtherChannel bundle? (Choose four.)
A. LACP system priority
B. LACP port priority
C. interface MAC address
D. system ID
E. port number
F. hot-standby link identification number
G. interface bandwidth
Correct Answer: ABDE
QUESTION 12
Refer to the exhibit.
Which configuration ensures that the Cisco Discovery Protocol packet update frequency sent from DSW1 to ALS1 is half of the default value?
A. DSW1(config)#cdp timer 90
B. DSW1(config-if)#cdp holdtime 60
C. DSW1(config)#cdp timer 30
D. DSW1(config)#cdp holdtime 90
E. DSW1(config-if)#cdp holdtime 30
F. DSW1(config-if)#cdp timer 60
Correct Answer: C
QUESTION 13
It a switch stack is configured to used SDM templates, where are the templates stored? 300-115 dumps
A. stack master
B. TFTP server
C. flash memory
D. all stack members
Correct Answer: A
QUESTION 14
Ferris Plastics, Inc. is a medium sized company, with an enterprise network (access, distribution andcore switches) that provides LAN connectivity from user PCs to corporate servers. The distribution switches are configured to use HSRP to provide a high availability solution.
– DSW1 -primary device for VLAN 101 VLAN 102 and VLAN 105
– DSW2 – primarydevice for VLAN 103 and VLAN 104
A failure of GigabitEthemet1/0/1 on primary device should cause the primary device to release its status as the primary device, unless GigabitEthernet1/0/1 on backup device has also failed.
Troubleshooting hasidentified several issues. Currently all interfaces are up. Using the running configurations and show commands, you have been asked to investigate and respond to the following question.
During routine maintenance, it became necessary to shut down the GigabitEthernet1/0/1 interface on DSW1. All other interfaces were up. During this time, DSW1 remained the active device for the VLAN 102 HSRP group. You have determined that there is an issue with the decrement value in the track command for the VLAN102 HSRP group. What needs to be done to make the group function properly?
A. The decrement value on DSW1 should be greaterthan 5 and less than 15. 0
B. The decrement value on DSW1 should be greaterthan 9 and less than 15.
C. The decrement value on DSW1should be greaterthan 11 and less than 19.
D. The decrement value on DSWTs should be greaterthan 190 and less than 200.
E. The decrement value on DSWTs should be greaterthan 195 and less than 205.
Correct Answer: C
QUESTION 15
VLAN maps have been configured on switch R1. Which of the following actions are taken in a VLAN map that does not contain a match clause?
A. Implicit deny feature at end of list.
B. Implicit denyfeature at start of list.
C. Implicit forward feature at end of list
D. Implicit forward feature at start of list.
Correct Answer: A
QUESTION 16
Refer to the exhibit.
Users of PC-1 experience slow connection when a webpage is requested from the server. To increase bandwidth, the network engineer configured an EtherChannel on interfaces Fa1/0 and Fa0/1 of the server farm switch, as shown here:
Server_Switch#sh etherchannel load-balance
EtherChannel Load-Balancing Operational State (src-mac):
Non-IP: Source MAC address
IPv4: Source MAC address
IPv6: Source IP address
Server_Switch#
However,traffic is still slow. Which action can the engineer take to resolve this issue?
A. Disable EtherChannel load balancing.
B. Upgrade the switch IOS to IP services image.
C. Change the load-balance method to dst-mac.
D. Contact Cisco TAC to report a bug onthe switch.
Correct Answer: C
QUESTION 17
Which two statements about SPAN source and destination ports during an active session are true? 300-115 dumps (Choose two.)
A. The source port can be only an Ethernet physical port.
B. The source port can be monitored in multiple SPAN sessions.
C. Thedestination port can be destination in multiple SPAN sessions.
D. The destination port does not participate in STP.
E. You can mix individual source ports and source VLANs within a single session.
Correct Answer: BD
QUESTION 18
Which two statements about the HSRP priority are true? (Choose two)
A. To assign the HSRP router priority in a standby group, the standby group-number priority priority-value global configuration command must be used.
B. The default priority of a router is zero (0).
C. The no standby priority command assigns a priority of 100 to the router.
D. Assuming that preempting has also been configured, the router with the lowest priority in an HSRP group would become the active router.
E. When two routers in an HSRP standby group are configured with identical priorities, the router with the highest configured IP address will become the active router.
Correct Answer: CE
QUESTION 19
Refer to the exhibit.
Which statement about switch S1 is true?
A. Physical port Fa0/13, Fa0/14, and Fa0/15 successfully formed a Layer 2 port-channel interface using an open standard protocol.
B. Logical port Fa0/13, Fa0/14, and Fa0/15 successfully formed a Layer 2 physical port- channel interface using a Cisco proprietary protocol.
C. Physical port Fa0/13, Fa0/14, and Fa0/15 successfully formed a Layer 3 port-channel interface using a Cisco proprietary protocol.
D. Logical port Fa0/13, Fa0/14, and Fa0/15 successfully formed a Layer 3 physical port- channel interface using an open standard protocol.
Correct Answer: A
QUESTION 20
Refer to the exhibit. What is the result of setting GLBP weighting at 105 with lower threshold 90 and upper threshold 100 on this router?
A. Only if both tracked objects are up will this router will be available as an AVF for group 1.
B. Only if the state of both tracked objects goes down will this router release its status as an AVF for group 1.
C. If both tracked objects go down and then one comes up, but the other remains down, this router will be available as an AVF for group 1.
D. This configuration is incorrect and will not have any effect on GLBP operation.
E. If the state of one tracked object goes down then this router will release its status as an AVF for group 1.
Correct Answer: B
QUESTION 21
A network administrator configures 10 extended VLANs ranging from VLANs 3051 to 3060 in an enterprise network.
Which version of VTP supports these extended VLANs?
A. version 1
B. version 2
C. version 3
D. VTP does not recognize extended VLANs.
Correct Answer: C
QUESTION 22
What is the default HSRP priority?
A. 50
B. 100
C. 120
D. 1024
Correct Answer: B
QUESTION 23
You have been asked to install and configure a new switch in a customer network. Use the console access to the existing and new switches to configure and verify correct device configuration.
ImageData src=”images/300-115_img_37.jpg”/>
ImageData src=”images/300-115_img_38.jpg”/>
You are adding new VLANs. VLAN500 and VLAN600 to thetopology in such way that you need to configure SW1 as primary root for VLAN 500 and secondary for
VLAN 600 and SW2 as primary root for VLAN 600 and secondary for VLAN 500.
Which configuration step is valid?
A. Configure VLAN 500 andamp; VLAN 600 on both SW1 andamp;SW2
B. Configure VLAN 500 and VLAN 600 on SW1 only
C. Configure VLAN 500 and VLAN 600 on SW2 only
D. Configure VLAN 500 and VLAN 600 on SW1 ,SW2 and SW4
E. On SW2; configure vtp mode as off and configure VLAN 500 and VLAN 600; configure back to vtp server mode.
Correct Answer: A
QUESTION 24
A network engineer is setting up a new switched network. The network is expected to grow and add many new VLANs in the future. Which Spanning Tree Protocol should be used to reduce switch resources and managerial burdens that are associated with multiple spanning-tree instances?
A. RSTP
B. PVST
C. MST
D. PVST+
E. RPVST+
Correct Answer: C
QUESTION 25
Refer to the exhibit.
A network engineer wants to analyze all incoming and outgoing packets for an interface that is connected to an access switch. Which three items must be configured to mirror traffic to a packet sniffer that is connected to the distribution switch? (Choose three.)
A. A monitor session on the distribution switch with a physical interface as the source and the remote SPAN VLAN as the destination
B. A remote SPAN VLAN on the distribution and access layer switch
C. A monitor session on the accessswitch with a physical interface source and the remote SPAN VLAN as the destination
D. A monitor session on the distribution switch with a remote SPAN VLAN as the source and physical interface as the destination
E. A monitor session on the access switch with a remote SPAN VLAN source and the physical interface as the destination
F. A monitor session on the distribution switch with a physical interface as the source and a physical interface as the destination
Correct Answer: BCD
QUESTION 26
Refer to the exhibit
A network engineer changes the default native VLAN to VLAN 999. After applying the settings on theuplinks to the core switches, the switch control traffic, such as CDP and VTP, is no longer working. The standard configuration is used for each uplink. What is wrong with the configuration?
A. The interface is administratively down.
B. The encapsulationtype is incorrect.
C. The switchport mode trunk command should be first in the output.
D. The native VLAN is not present on the trunk.
E. The control traffic must be manually enabled on the new native VLAN.
Correct Answer: D
QUESTION 27
Which private VLAN access port belongs to the primary VLAN and can communicate with all interfaces,including the community and isolated host ports? 300-115 dumps
A. promiscuous port
B. isolated port
C. community port
D. trunk port
Correct Answer: A
QUESTION 28
A network engineer notices inconsistent Cisco Discovery Protocol neighbors according to the diagram that is provided.
The engineer notices only a single neighbor that uses Cisco Discovery Protocol, but it has several routing neighbor relationships. What would cause the output to show only the single neighbor?
A. The routers are connected via a Layer 2 switch.
B. IP routing is disabled on neighboring devices.
C. Cisco Express Forwarding is enabled locally.
D. Cisco Discovery Protocol advertisements are inconsistent between the local and remote devices.
Correct Answer: A
QUESTION 29
A server with a statically assigned IP address is attached to a switch that is provisioned for DHCP snooping. For more protection against malicious attacks, the network team is considering enabling dynamic ARP inspection alongside DHCP snooping. Which solution ensures that the server maintains network reach ability in the future?
A. Disable DHCPsnooping information option.
B. Configure a static DHCP snooping binding entry on the switch.
C. Trust the interface that is connected to the server with the ip dhcp snooping trust command.
D. Verify the source MAC address of all untrusted interfaces withip dhcp snooping verify mac-address command.
Correct Answer: B
QUESTION 30
Which option describes a limitation of LLDP?
A. LLDP cannot provide information about VTP.
B. LLDP does not support TLVs.
C. LLDP can discover only Windows servers.
D. LLDP can discover up to two devices per port.
Correct Answer: A
What Our Customers Are Saying:
The best and most updated latest Cisco CCDP 300-115 dumps exam practice materials in PDF format free download from leads4pass. Useful latest Cisco CCDP https://www.leads4pass.com/300-115.html dumps pdf training resources which are the best for clearing 300-115 exam test, and to get certified by Cisco CCDP. It is the best corrct choice for you to pass Cisco 300-115 exam easily.
Latest Cisco CCDP 300-115 dumps vce youtube: https://youtu.be/wyXFLuYtFpI
Why Select leads4pass?
leads4pass is the best provider of IT learning materials and the right choice for you to prepare for the exam. Other brands started earlier, but the price is relatively expensive and the questions are not the newest. leads4pass provide the latest real questions and answers with lowest prices, help you pass the exam easily at first try.
